Daikin FXHQ-A Especificações descarregar pdf (Página 25)

Installation EDUS39-600-F5

24 FXHQ-M

DANGER

• Use of oxygen may cause an explosion resulting in serious

injury or death. Only use nitrogen gas.

CAUTION

• Be sure to insulate any field piping all the way to the piping

connection inside the unit. Any exposed piping may cause

condensate or a burn if touched.

6-4 PIPING INSULATION

• Make absolutely sure to execute thermal insulation works

on the pipe-connecting section after checking gas leakage

by thoroughly studying the following figure and using the

insulation pipe cover (6) and (7). Fasten both ends with the

clamps (4). (Refer to Fig. 16)

• Wrap the small sealing pad (9) only around the insulation

for the joints on the gas piping side. (Refer to Fig. 16)

(1) For rear-facing piping:

• Remove the rear metal plate for pipe. (Refer to Fig. 17)

• The figure shows when both the piping and drain pipe are set

facing the back.

When setting the piping to face up or right, attach the rear

metal plate for refrigerant pipe and plug a hole for drain pipe.

See Page 186, Section 4. PREPARATIONS BEFORE

INSTALLATION, (3-3).

(2) For piping facing up.

• When setting the piping to face up, the L-shaped branch

pipe kit sold separately is required.

• Removing the top penetration lid and use the L-shaped

branch pipe kit sold separately to set the pipe. (Refer to Fig.

18, 19)

(3) For piping facing right.

• Cut out a slit hole on the decoration panel (right) and set

the pipe. (Refer to Fig. 17)

• When piping is complete, use sissors to cut the removed

penetration lid into the shape of the pipe and attach.

As when removing the top penetration lid, secure the lead

lines for the swing motor and thermistor by passing them

through the clamp section on the top penetration lid.

(Refer to Fig. 18, 20)

Insulation pipe cover for gas pipe (6)

Gas pipe

Liquid pipe

Insulation pipe cover for liquid pipe (7)

Clamp (4) (× 4)

Attach to the bottom

(For both gas pipe and liquid pipe)

Procedure for thermal insulation of liquid-side pipe

Insulation pipe cover for

liquid pipe (7)

Orient so that the end of

the wrapped insulation

material is facing up

Flare nut connection

Insulation pipe cover (main unit)

Attach to base

Main unit

Clamp (4)

Insulation pipe cover

(Locally procured)

Procedure for thermal insulation of gas-side pipe

Insulation pipe cover

for gas pipe (6)

Insulation pipe

cover (main unit)

Attach to base

Orient so that the end of

the wrapped insulation

pipe cover is facing up

Flare nut connection

Insulation pipe cover

(Locally procured)

Wind around the

pipe, beginning at

the base.

Small sealing

pad (9)

Fig. 16

Right-facing drain pipe

Right-facing

refrigerant

piping

Decoration panel (right) removable part

If only setting the drain pipe to

face right, cut this section only.

Fig. 17

Rear-facing

refrigerant pipe

Rear right-facing

drain pipe

Top plate

Top penetration lid

Cut out

Fig. 18 (A figure from an inside bottom)

This hole not using it.

Fig. 19

Upward-facing

refrigerant pipe

L-shaped branch pipe

kit (Optional accessories)

Top penetration

lid clamp section

Thermistor lead line

Swing motor

lead line

Fig. 20 (A figure from an inside bottom)

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 35 36

Comentários a estes Manuais

Sem comentários

Daikin FXHQ-A Especificações Página 25

Comentários a estes Manuais

Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" Daikin FXHQ-A